搜索资源列表
protus_abc
- 仿真了常用单片机器件,自己写的,包含1602 6264 8255 4*4按键 ADC DAC 数码管 LED 串口,继电器,直流电机等,将它们综合一起仿真,完整的程序 -Simulation of a common microcontroller devices, to write, including 1602626482554* 4 buttons ADC DAC digital LED serial ports, relays, DC motors, etc., they are inte
ZX
- 8255C口接逻辑电平开关K0~K7,A口接LED显示电路L0~L7,编程从8225C口输入数据,再从A口输出-8255 C port logic level switch K0 ~ K7, A port LED display circuit L0 ~ L7, programming input the 8225C port, and then the A port output
ProteusWith8086
- 使用proteus基于C语言编写的8086模拟的实验,共7个,清单如下: 0.串口流水灯 1.串口IO口读写控制LED 2.8255开关控制LED 3.7位数码管显示 4.四乘四键盘输入 5.步进电机 6.AD数模转换-Up to 7 Proteus experiments base on 8086.With C code.
编码显示器
- 利用8255扩展并行端口(硬件电路参见CodeDisplay_8255.DSN)。当KEY按下时,利用8255的PC口输入二进制值编码(6位),将该值转换成十进制后显示在2位7段LED显示器上。(Using 8255 to extend parallel ports (see CodeDisplay_8255.DSN for hardware circuits). When the KEY is pressed, the binary value encoding (6 bits) is ent
单片机实验报告
- 单片机实验,实现一些单片机实验,基本并行I/O口实验 扩展并行I/O口实验 静态LED显示实验 矩阵键盘扫描实验 LCD 1602显示实验 ADC0808/9信号采集实验 按键声报警实验 8255扩展I/O口及交通信号灯控制实验 7279键盘扫描及动态LED显示实(single-chip computer experiment)
汽车控制系统
- 汽车信号灯控制系统 单片机实现摘要:随着汽车制造技术及电光源技术的发展而逐步完善的。它经历了机油(或煤油)灯、乙炔气灯到电光源灯的发展历程。现代汽车信号灯灯具已经开始使用发光二极管(LED)技术以及光导技术,这是信号灯灯具的一次飞跃。现在我们就是利用微机原理的知识用8088,8255,8253等几种芯片来控制汽车的信号灯。(A summary of the realization of the single chip microcomputer for the control system of
微机原理综合设计实验-数字电压表A.rar
- 利用ADC0809采集电位器的电压值,将采集的电压值通过8255显示在七段数码管上,显示数据保留小数点后2位,利用8253定时数据更新,每隔0.5秒数据更新一次。扩展要求:具有设置报警阈值功能,当超过阈值时,点亮一个LED灯。(Using ADC0809 to collect the voltage value of potentiometer, the collected voltage value is displayed on seven digital tubes through 825